How to connect 3 gang 1 way light switch 3-gang 2-way 10ax switch white (1892d)

Dear Mrs J,Thanks for your email,FITTING INSTRUCTIONS FOR ULTIMATE MOULDEDAND FLAT PLATE ACCESSORIESRead these instructions fully before commencing workand retain them for future reference.SAFETY INSTRUCTIONSThese accessories are to be installed in accordancewith the current edition of the IEE Wiring Regulations(BS 7671: Requirements for Electrical Installations)and appropriate statutory regulations.In the Republic of Ireland the installation must be inaccordance with the ETCI National Rules for Electricalinstallations - ET 101.4. When mounting flat plate accessories, for the bestresults and visual appearance, it is recommendedthat prior to installation, the mounting surfacebeneath the accessory frontplate is first preparedto ensure that it is flat and all high spots have beenremoved.5. Certain accessories may require that the top andbottom lugs in 1 gang, 4 lug boxes, are bentinwards and out of the way to ensure the correctinstallation within the box.6. Always use cable of the correct rating and type.7. The layout of the terminal connections may differbetween fittings, carefully check the location of theterminal connections before wiring.9. Secure the accessory to the wall by means of thefixing screws provided, positioning the cables inthe box so as to avoid them being trapped.10. Replace the appropriate fuse, or switch on theappropriate circuit breaker. Switch on the mainsisolator switch.IMPORTANT NOTICEWIRING COLOUR CHANGESAs from 1st April 2004 new installations in theU.K. could be wired using the new EU harmonisedcolours for the supply conductors of twin andearth cable:New colours Old coloursBROWN - LIVE RED - LIVEBLUE - NEUTRAL BLACK - NEUTRALThe old colours will cease to be used from1st April 2006.10 AMP 1 GANG 2 WAY SWITCH (1 WAY SWITCHING)Connect the cables as shown in the wiring diagram.10 AMP 1 GANG 2 WAY SWITCH (2 WAY SWITCHING)Connect the cables as shown in the wiring diagram.10A 1 GANG 1 WAY AND 2 WAY SWITCHADDITIONAL FITTING INSTRUCTIONSThis switch has been designed for installing in a16mm deep wall box. It is therefore suitable forretrofit installations providing:a) Cables enter from the top of the wall boxb) Wall box does not protrude from the wallIf cables enter from the side of the wall box thenit is likely that it will need replacing with a deeper25mm box.10 AMP 2 GANG AND 4 GANG 2 WAY SWITCHConnect the cables as shown in the wiring diagram.4 gang switch: Wire each circuit to individual switches.10 AMP 1 GANG INTERMEDIATE SWITCHIntermediate switches are used if more than two switchesare required to control a two way lighting circuit.They should be fitted between the first and last switcheson the circuit.One particular wiring arrangement, which may be usedis shown in the following diagram.If replacing an existing switch, note the location of theterminals and the colour and position of cableconnections. Ensure that all cables are connected tothe corresponding terminals on the new switch.10 AMP 1 GANG TRIPLE POLE DISCONNECTORFor use with extractor fans fitted with or without timercontrol. Provides local isolation for maintenance or repairwithout the need to isolate the complete circuit.Connect the cable conductors as shown in the wiringdiagram, ensuring that the correct polarity is maintainedbetween the load and supply conductors.For extractor fans without timers, there will only be twoload and two supply conductors.20 AMP DOUBLE POLE SWITCHESConnect the cables as shown in the wiring diagram.Ensure that the load cable is connected to the applianceWhen used on a ring main there will be two supply cables.Connect both of the cables to the same terminals.For switches with flex outlets, pass load cable throughoutlet before connecting to switch. Ensure cable clamp isfitted and tightened across outer sheath of cable.13 AMP SINGLE SWITCHED SOCKETConnect the cables as shown in the wiring diagram.The diagram shows connections for a ring main circuit.For radial circuits or a spur off a ring main there willonly be one cable.13 AMP UNSWITCHED SOCKETConnect the cables as shown in the wiring diagram.The diagram shows connections for a ring maincircuit. For radial circuits or a spur off a ring mainthere will only be one cable.13 AMP 2 GANG SWITCHED SOCKETConnect the cables as shown in the wiring diagram.The diagram shows connections for a ring main circuit.For radial circuits or a spur off a ring main there willonly be one cable.5 AMP SINGLE UNSWITCHED SOCKET ROUND PINConnect the cables as shown in the wiring diagram.Do not connect this socket directly to a ring maincircuit. It should only be connected to either a radialcircuit, protected by a MCB/fuse of the appropriaterating at the consumer unit/fuseboard, or spurred froma ring main and protected by a fused connection unitfitted with a fuse of the appropriate rating.G2515Top Intermediate ModLL1 L2LL1 L2L3 L4L1 L2NOTE: IF YOU ARE IN ANY DOUBT ON HOW TOPROCEED, CONSULT A QUALIFIED ELECTRICIAN1. Switch OFF the mains supply and remove theappropriate fuse or switch off the appropriate circuitbreaker before commencing installation. Ensure thatno one else has access that would enable the supplyto be inadvertently reconnected.2. Remove the existing accessory from the wall (if usingthe new accessory to replace an old one).3. Remove any plaster debris and dust from the insideof the mounting box (wall box). Ensure that the headsof any box fixing screws do not protrude into the box.Individual conductor lengths shall be no longer than65mm including 10mm bared copper for termination.It is also recommended that the individual conductors,once connected, are dressed around the sides of theswitch to ease switch installation in the box.Ultimatemouldedand flat plateTO EARTHTERMINALIN BOXLIVESWITCHED LIVESWITCHED LIVELIVETO EARTHTERMINALIN BOXLIVESWITCHED LIVE LIVETO EARTHTERMINALIN BOXSWITCHED LIVETO EARTHTERMINALIN BOXSWITCHED LIVE LIVETO EARTHTERMINALIN BOXSWITCHED LIVE10 AMP 3 GANG 2 WAY SWITCHConnect the cables as shown in the wiring diagram.TO EARTHTERMINALIN BOXLIVESWITCHED LIVETO EARTHTERMINALIN BOXLIVETO EARTHTERMINALIN BOX

Manufacturer	Nexus (Jiaxing)
Part number	843-01
Item Weight	90.7 g
Product Dimensions	8.6 x 2.3 x 8.6 cm; 90.72 g
Item model number	843-01
Size	Triple
Colour	White Moulded
Style	Light Switch
Finish	White
Power source type	AC/DC
Wattage	5000 watts
Installation method	Screw-In
Item Package Quantity	1
Switch Type	2-way
Plug profile	Wall Mount
Included components	socket
Batteries included?	No
Batteries Required?	No

BG Electrical Triple Wall Light Switch, 2 Way, Round Edge, Nexus 800 Series, White Moulded, 20A, 16AX, 843

Details

Description

Specifications

Have a Question? See What Others Asked

Common Questions