Raspberry Pi Camera Case/Enclouser - Black Assemble in 30 secs

Mildly tricky to insert the camera. Everything falls apart if dropped, but didn't break.

Does not close properly, will not latch. Garbage.

This ultimately worked for me, but not until I made some modifications to it. Both the V1 and V2 camera modules had the same problem. I also destroyed a perfectly good camera module in the process. The hole in the front doesn't align with the camera so you can't get it in all the way. I had to carve about 1/8" away from the bottom of it with a utility knife which resulted in an oval hole. It looks a bit weird, but the camera module now slips on. I think the module was damaged when I put pressure on it trying to assemble it before I modified the case. Also, the plastic tab that projects from the back cover to hold the camera module in place was too long so I had to trim that down to be able to get the case to close. All things considered it was an expensive case since I had to buy a replacement camera module.

Bought this as a case for a noir camera to use as a nanny cam. It blends in perfectly with my A/V equip so it doesn't look obvious. I have it connected to my RPi3 case with dual sided tape. Case is sturdy and the camera fits perfectly in slots though you do have to push it in for it to click in place. In the future I plan on getting a longer ribbon for a 2nd camera and with mount this to a wall as a security camera. There is a great tutorial on element14 for making a motion camera and I plan on ordering another case for that project.

Tight fit. Too tight to fit the camera modules withough a little filing practically everywhere. Not sure who designed them, but an extra 1/32 of an inch of room anywhere wouldnt have killed ya, would have made the product way better, instead of breaking the module trying to make it fit.

Trying to fit the camera into this case and get the camera lens to align with the hole in the front of the case is an exercise in frustration. Trying to get the lens in the hole actually caused the micro connector on the camera itself to separate from its pcb board, making me think my camera was dead. I had to disassemble everything, test the camera cable to make sure bending it to fit in this case didn't short a lead, and remount everything. It was only upon close inspection of the camera board that I noticed its connector had popped loose. Everything about the mounting system of this case is poorly designed. You have to try to slide the camera module down four little plastic shafts, while the board rocks forward and backward, making it a delicate dance to try to line the camera lens up with the hole in the front of the case. Even if you do get it to align and the camera lens to actually go in the hole, it puts pressure on the camera pcb when you snap the case together and it very well may knock the micro connector loose again. This is one of the worst small enclosure/case experiences I've ever had, and I've been at this for 30 years, so that's saying something. Save your money and look elsewhere.

Good Case. a little difficult getting it to fit just right, but not impossible. Once its in place it stays secure.

Together this makes for very flexible positioning that holds firmly. The base of this mount is a strong magnet. This pan/tilt base is low cost but solid, and obviously hand operated - as with no servos.

カメラモジュールのケースが無いとスタンドできないので仕方なく買いました。 少しお高いので結構迷いましたが、買って大正解でした。 見た目がシンプルで、ネジ要らずでセット可能。 カメラランプの赤い点灯も、ぽっち穴が空いていて見えるようになっています。 台などに取り付けられるように、ネジが同梱されています。

Does not fit v2.1 camera at all, camera does not align with slots provided.

Great item

The Camera fits snuggly into this case as if they were made for each other. It is dainty so handle with care.

No encaja con la camara, la camara se desconecta cuando inteno ponerla en la carcasa.