Yale Security Lock 2 Touch, Black Biometric Fingerprint Door Lock with Keypad, Unlock with Your Code or Your Fingerprint (No Wi-Fi), YRD420-F-BLE-BSP

I recently bought and installed two Yale Assure Lock 2 Touch door locks. I elected to get the keyless version with Bluetooth only. It doesn't take too much searching to find plenty of YouTube videos that show how easy it is to defeat conventionally keyed locks. So right off the bat, going keyless was a step up in security. I chose the Bluetooth-only option mainly to keep battery drain to an acceptable level. But it's also the case that I have no need to remotely activate my locks or view their status - never had it and don't need it. On the other hand, without a Wi-Fi-enabled lock you lose geofencing capabilities and remote/timed entry for house cleaners, dogwalkers, and guests. Here though, something that isn't mentioned (or is easily missed) in their sales info is that Yale does not recommend using keyless locks if you only have one entry door because you can be locked out if there is a lock failure. That warning appears in the user's manual. But with the Assure Touch, there are three ways to open the lock: finger touch, keypad code, or with the app if you are within Bluetooth range. And if the batteries go dead, you can touch a 9-volt battery to contacts on the underside of the keypad to enable the lock. So there is plenty of built-in redundancy. It seems like the only failure mode would be if the actual motor-driven locking mechanism somehow broke or jammed. But there is redundancy there if you have these locks on more than one door since the chances that two locks would fail at the same time is probably highly unlikely. Installation was relatively easy but if you don't know what end of a screwdriver to pick up or are intimated by putting together Ikea furniture, it might be a challenge. My main issue came after installation. The user manual is very good in explaining the installation but not so much with getting the app up and running. After install, the manual just tells you to follow the instructions on the app on your cell phone. But I found it like following a road detour and suddenly there are no more signs to follow. I did not find either the app or user manual documentation to be forthcoming in telling you how to configure the lock and how to add other people. You can grant access to other homeowners and guests but it's not immediately clear how. I suppose there is always Google there to help, but at least at the time of this review, there is a 24/7 Yale customer hotline that proved to be quite responsive and helpful. But after you explore the app and get used to it, it offers a lot of functionality. I opted to install the Yale DoorSense hardware (which is nothing more than a little magnet) that lets the door "know" when it is opened or closed. This enables to door to automatically lock at a time delay of your choosing. So there's no more I-wonder-if-I-locked-the-door anxiety when you leave. You can also program in the number of tries someone gets to guess your keypad entry code before getting locked-out for a period of time that's also programmable. But the best part of the lock is the touch entry. It is amazing. You just have to touch (importantly, not press) the finger of your choice on the fingerprint reader and the lock opens instantly (you LOCK the door using any finger). Easy and convenient. This is a well thought-out lock that looks great and is easy to use. I very much recommend it. The only thing left to be assessed is how well it performs over time in regular use. But my immediate impression is that they are very well made and likely to go the distance. Update 7/17/2025 I chose the Bluetooth only version of the Assure Lock 2 instead of the WiFi version mainly to keep the battery drain to an acceptable level although at the time of purchase, I didn't know what to expect in the way of battery life. I just changed the batteries in my lock for the first time almost exactly a year after I installed it. The lock is on the door from the garage into the house and is my most used door. Changing batteries once a year is more than acceptable to me. Your mileage may vary. I also have an Assure lock on my front door that was installed a little later than the garage door. This door is used much less frequently than the garage door. So far I have not gotten a low battery warning. The low battery warning appeared on my phone app and indicated there was 20% battery remaining. One other observation is that somehow and for some unknown reason the locks get scrambled such that the lock/unlock status and door open/closed status do not agree. I have an idea what may cause this but can't say for certain that I'm on the right track. No matter. This has happened very rarely and is easily corrected by simply recalibrating the lock.

The Yale lock is a perfect example of bad engineering. The lock is beautiful looking, with a very clean design, but has some horrible issues that make it impossible to recommend. Issue #1 - Yale breaks the whole concept of Apple's Home app with this design. With Apple Home, we often share our Home to family members when they housesit or are staying at our house. All of our 80+ accessories work flawlessly, EXCEPT Yale. This is a problem when unlocking the front door is a critical requirement for housesitting. For these family members, the door lock in the Home app says "SETUP NEEDED". It turns out this is because Yale requires anyone using the Home app to also have the Yale app installed, to personally have enabled Home sharing between Yale & Home apps, and to be a FULL ADMINISTRATOR in the Yale app. The point of the Home app is I can avoid using these third-party apps, and that I can share access without requiring everyone else to install these third-party apps. And, no, I don't want my mother or cousin to be an administrator in Home or Yale, with the ability to remove accessories or change critical settings. This is bad, insecure design and incredibly frustrating. Issue #2 - Fingerprints. I bought this more expensive model because the idea of a TouchID-like experience for my front door sounds wonderful. However, the setup process is incredibly error-prone, with the lock often flashing red and the app showing an error message when trying to setup fingerprints. Yale's helpful support article suggests you factory reset the lock when you get the error message (thanks!) even though it requires complete re-setup of the entire lock, and even though the error message eventually goes away if you re-attempt a few times per day until it works. Even once fingerprints are registered, for most family members it works less than 50% of the time, and I appear to be the only one who considers using my fingerprint an option. WORST OF ALL, the fingerprints disappear from the lock once every time you change the batteries (which is more often than the advertising suggests), but the app will tell you that they're still registered. So you first have to unregister each fingerprint, and then re-register each fingerprint, multiple times per year! And again, this process will likely take several days to complete, with you entire family frustrated throughout the process and telling you that you wasted hundreds of dollars on a complete piece of crap, and can we please just go back to using a physical key again, it was so much simpler. Issue #3 – Battery life. Even though we don't use our front door super often, and even though we have strong WiFi signal at the front door, and even though we purchase high quality batteries, the battery life is pitiful, and we have to change them about twice as often as the manual suggests. Rechargeable batteries are not allowed (and will immediately flag a low-battery warning), so this lock is bad for the environment as an energy-hungry device that requires the frequent disposal of AA batteries in a home where we otherwise use 100% rechargeable batteries. But the most annoying part is that this necessitates the fingerprint issue mentioned above. Issue #4 – Entry code sensitivity. Compared to the prior model of Yale HomeKit lock which we used at our last house, this model is very finicky when it comes to entering the entry codes to unlock the door. I typically have to enter the code 2-3 times to get it to register. This is due in part to two poor design choices: the backlit numbers are dimly backlist, making it a bit hard to see them in direct sunlight; and the sound when tapping in the numbers is very quiet, making it hard to hear when you have tapped successfully on a number. Between these two features, it's quite easy to mis-type the code. At this point I'm on the lookout for a replacement device. I personally love the idea of not having a keyslot on the front door, but I may have to give up on this preference for the sake of getting a more functional smart deadbolt in a house full of otherwise mostly flawless home accessories.

The lock (Yale Assure Lock 2 Touch YRD450-F-BLE-BSP) has excellent features, with fingerprint unlock which works fairly well and 'one-touch' locking from the outside. From the inside, the knob is turned to lock/unlock the door. This lock is the 'second' lock on the door. We purchased this lock particularly because it does *not* have a key (which could be picked), because it has decent batteries (4 x AA) and because Yale is a reputable lock brand. As some other reviews mention, although sold by amazon.com.au, the lock doesn't seem supported in Australia (or anywhere other than USA/Canada). This results in - for us - two separate problems (1) extra steps involved in configuring the lock with the 'Yale Access' or 'August Home' app (2) connecting the lock to the local network The second problem I have not been able to solve. As of July 2024, the 'Yale Access' app and 'August Home' app does not recognise the 'Yale Connect Plus Wifi Bridge' (currently sold in Australia) and the 'Plus' bridge is not listed in the manual product selector choices. I purchased the older version of the Wifi bridge (the version which is not 'Plus', and is no longer available from standard shops in Australia). Although I could connect to that older Wifi bridge with the app, trying to connect that Wifi bridge to the lock is not successful (the app reports an error). Another Amazon review - and an oblique reference on the Yale website - mentions that Yale Assure Lock can connect to the Wifi bridge, so I don't know if that is a problem with buying the Australian version of the old Wifi bridge or because the App doesn't like being outside North America (although I'm using an VPN). Sadly, z-wave standards are different in Australia compared to the USA, and there are some reports that using the Yale Assure 2 wifi module is detrimental to the lock's battery life. The first problem is solveable. As of July 2024, it *cannot* be configured with the "Yale Home" app which is available to Australian users of Google Play. Either the "Yale Access" app needs to be installed from another source or the "August Home" app can be used (available in Google Play for Australian users). Both these apps will not allow a lock to be 'added' to the 'home' unless the app believes the user is in the USA or Canada. Some other users mention using an American phone number. I used an Australian phone number, but used a VPN to 'fake' a USA location.

Was great when it worked. After about 3 months it stopped. Followed all support and replaced batteries and reset to factory settings.. it's useless. Very disappointed.

Over 50% of the time, the one-touch sensor will not lock the door. If you press it again, it thinks you're trying to lock the door; it then lights up as if it has locked, but it's not. So every time you lock the door, you then have to check the handle to confirm. I have reached out to Yale a number of times with no response.

Si vives en México NO LA COMPRES, NO ES COMPATIBLE, la aplicación para controlarla por wifi solo funciona en Europa y Africa. Hablé a soporte de Yale México y me dijeron que no tenía soporte para esa cerradura ni para la app que la controla por que no es un modelo para México.

Had the Assure Lock for more than 3 years with no issue. When this fingerprint model came out, I made the switch. Ordered during Black Friday sale and got it delivered in early December. Installed it and was working well, until yesterday. Just slightly more than 2 months since installation, I got locked out of my house. Nothing worked. HomeKit, Yale app, PIN, fingerprint. Thought perhaps the battery died, tried a 9V to the pins on the outside of the lock, doesn’t work either. Waited for an hour to try, still couldn’t get anything to work. To only way was to get a locksmith to drill through the lock, and in the process getting it destroyed. I suspect the front panel facing outward was faulty, and caused everything to stopped working. Once the locksmith severed the connection to the front panel by cutting the wire, the back panel with the single button worked miraculously. Somehow it reconnected via Yale app and HomeKit, and batteries proved to be still working as the motor still worked. However at this stage, the front panel was already destroyed since I was locked out of the house. Although the first gen was good, I have totally lost faith in this 2nd gen product. Be wary when purchasing this product.