Orion Motor Tech Rear Axle Bearing Puller Tool Set, Rear Axle Bearing Remover Set, Rear Axle Bearing Removal Tool Kit with 3 Sizes 1-1/4 to 1-7/8, 1-5/16 to 2-3/8, & 1-3/8 to 2-7/8

Put up with 5lb slider hammer and some hard to remove bearings. Bearings wouldn't budge before I tried this. Worth every penny. Be sure to snug the bolt down, give it a wiggle and check it is still snug. Easy to use. Quality is par at least for the home mechanic. I wouldn't do another axle bearing without this. Made the job much easier. Worked good for me, and reduced my effort. Still I would use a good slide hammer with a decent weight slide. 2014 Ford Raptor axle bearings with 100k miles of rough terrain for reference. Before the tool, tried old fashioned triple claw with no progress. After this tool, the job is done. The example above is so you know it wasn't an average job. You may sweat a little, but it will still be less than without the tool. Glad I have this set in my toolbox.

Ignore the negative reviews about these they work as intended with a compatible slide hammer. The only concern I had with this tool was that the pins that hold the rocker in place that pulls the bearing are not seated properly or at least on the set I received were not. I was able to pull both rear axle bearing out. However upon removing the second bearing from the tool the pin on the rocker had partially popped out. I fixed this by using a flat punch and hammer to make sure it was back in place properly. Also make sure you have a compatible slide hammer. I assume I’m not the only one who has experienced quality control issues with this product overall happy with my purchase.

Good tool, it does exactly what it should. Check out my video.

Looked good but on the first use the puller broke striking me in the lip busting it open and I thought I had damaged a couple of teeth but fortunately they were ok. Use with extreme caution!! One star is way overrated. Definitely wear safety glasses and a face shield and gloves wouldn’t be a bad idea. Update: even though the puller broke and my opinion of this particular tool hasn’t changed I have to say this seller contacted me and made a full refund without me even asking for one. I have to say they went above and beyond to make it right. I won’t hesitate to give them another try in the future.

This tool helped with a 1990 GMT400

Very good puller for the price. Work great for my 77 K5 Blazer axle bearing removal.

It's pretty good but the washer did break during the first use. I think it’s worth buying if you have a good slide hammer.

great price and product

fantastic kit if you already have a slide hammer. used the kit to pull and replace 67-72 c10 12bolt axle bearings. easily slipped in and pulled out the first side in a minute or so. second side was siezed from rust more, and took 20 slide-hits, but made it no issues. 10/10. solid build, no wear and tear on the first pulls, not worried about bending like some cheaper steel out there.

Excelente para suspensiones y baleros de rueda. Automotriz.

Todo parece que es de buena calidad y espero me sea muy util ya que aun no lo utilizo

I don’t usually take the time to write reviews, but this tool definitely earned one. Going into this job, I honestly wasn’t expecting the best results. I was dealing with a stubborn axle bearing that was completely stuck, and I had already tried a few other methods. Once I got this puller set up, it completely changed the game. I put it through a pretty tough test, lots of solid hits with the slide hammer, and it held up extremely well. No slipping, no bending, just did exactly what it was supposed to do. In my case, the combination of the welding trick, a bit of heat, and this puller was the only way I was getting that bearing out. Without this tool, I’d probably still be fighting it. Really impressed with the durability and how well it performed under pressure. Definitely worth having in the toolbox.

This tool worked great. You would be better off to order the one with the slide hammer. I happen to have an old slide hammer. I modified with some welding. Used it on gm 10 bolt rear end to pull inner axle bearings. Good quality