Heavy Duty Furniture Leveling Feet Adjustable Furniture Leg Levelers for Tables Chairs Cabinets Sofa Raiser, Support 1320LBs, T- Nut Kit 3/8”-16 Thread, Large Base,w/ 4 Felt Pads,12 Screws (4 Pack)

Good quality product, perfect fit, works great

No more scratched porcelain floors! These are very heavy-duty adjusters. They look clean and they were very easy to install.

This leveler is everything you want. Extremely heavy duty and very well built. The teflon sliders work pretty well on my smooth concrete garage floor. I took the other ones that failed miserably back to home depot and got a refund. Yes I would buy these levelers again. They are truly wonderful. Full Dislosure I payed full pop for these and they are worth every penny !!!!

As mentioned here often, the T-nut mounting screw holes are countersunk and the package does not include such. I would not use either the supplied screw(as the quality is an unknown) nor would I use a countersink screw. I would use a #8 x 3/4(or 1") washered cabinet screw(GRK or similar). They have a nice flat, wide head to cover the entire countersunk hole, have a high tensile and grip strength, are much narrower than the predrilled flange hole so the screw can be moved further away from the center of the nut to grab more of the meat of the leg, will NOT BREAK off in the wood and are SELF TAPPING... so no pilot hole needed. What this kit also does not include are locking nuts. Great... I can level it by adjusting the leg, but if I move it around then what happens if I move it to clean and push it back?? The threaded legs and T-nuts have a very loose fit. Murphy says it will happen. Also, as others have noted the T-nut body dimension is too large for the installation prescribed 1/2" hole. I measure 0.515" near the top, flaring to up to 0.545"(!) at the back of the flange so you would run the risk of splitting the end of any type of hardwood. My suggestion for install is to run a 7/16" hole to a depth of close to, but not over, 2" (3/8" hole if you can run the bit in square with the leg for a close fit) then follow it with 9/16" to a depth of 3/4" for the T-nut clearance. The positives here are that the legs and flanges are heavy duty and the nylon is very hard. Added thought: When installing, a short piece of 3/8 threaded rod installed on the T-nut and inserted into the pre-drilled hole will allow you to center the nut in the correct position and gives you the added benefit of having full access to the flange face in order to secure the screws properly.

The original disk shaped plastic leveling feet that our kitchen table had were broken from when I move the table to clean the floor. The feet would get caught in the grout lines and snap. This caused the table to not be level and it has been crooked for years. I bought these new leveling feet without even knowing how our original ones were connected to the table legs. Amazingly, these feet worked perfectly! I unscrewed the original feet and these screwed right in place! Such an easy fix and now I have a perfectly leveled kitchen table! I wish I would have replaced the broken ones years ago!

These worked very well. Nice and sturdy. I made a butcher block table for my son's meat cutting room.

Great addition to work bench. My floor is terribly unlevel. These solve the problem.

A nice sized support foot, easy to install with a 9/16" drill bit. The threaded foot moves up and down smoothly and has a nice nylon pad on the bottom with a self adhesive felt pad you can add if needed. My only gripe is that the screws do not have a counter sunk head even though the mount has counter sunk holes and about 25% of the screw head broke of with very little pressure, even with a pilot hole. Use your own screws and these would be pretty decent adjustable furniture feet.

I have an antique Kauri Pine top side table which I have refurbished and one leg was a fraction shorter than the others. These levelers saved me the trouble of having to try to even the legs up and they look fabulous. So good to have felt pads under the feet so I can easily slide this table on the floor with no scratching etc. Great product.

Simple to install and came with felt cushions so if you wanted to not mark a floor maybe, with the nylon end, the felt would prevent that. Has a long shank so that the table leg adjustment could be over 1 inch.

Good quality

This product beats all competition. The design is superior for 2 reasons: 1. All loading is normal to the screw so no chance of popping off. 2. All the loading doesn't actually go on the wooden furniture but rather on the threads of the screw which is more than strong enough to take it. I added a 3/8" washer and nut to reduce load on threads and reduce the wobbliness of the connection.

Purchased to put on outside garden bench, which had rot on the legs. Cut off the rotten wood and installed the feet. You need a large drill bit to produce the hole for the fitting. Ability to have different heights on the feet was very helpful to ensure the bench was level. Sturdy and raises the wooden legs off the ground so no more rot. should ensure many years further use of the garden bench.