NETGEAR 8 Port PoE Gigabit Ethernet Easy Smart Managed Switch (GS308EP)

I run a Home-Lab that includes 2 of these little PoE switches. Working in an Enterprise IT environment, I would often forget that these smaller residential/hobby switches exist, but gosh to I love them. Not only are they cute, but they provide that enterprise level functionality with PoE. This means it could be used to wire up a PoE security camera system, handling both your network connection and power in one cable! Minus the countless other applications of PoE, this switch provides ample value for what you're paying. The build quality even on a switch this small is great! Feels heavy and sturdy but could honestly be held up by a number of command strips (Please... don't do that though!!!). I haven't noticed any problems with my unit getting too hot or needing anything special to operate as intended. All 8 ports work as expected and the throughput is, in fact, Gigabit as advertised. So no problems there. If you are looking for something consolidated but powerful, this could be for you!

I’ve been using this switch for several months now, and it’s been completely reliable. Setup was as simple as it gets. Plug it in, connect devices, and it just works. No configuration needed, which is exactly what I was looking for. I’m using it to power and connect multiple devices over PoE, and it has handled everything without any drops or instability. Once it’s up, you don’t have to think about it, which is what you want from a switch. Build quality feels solid, and it runs without any noticeable issues during normal use. Pros True plug-and-play setup Reliable over several months of continuous use Handles PoE devices without issues Stable connection with no dropouts Cons No advanced management features (expected for this type of switch) Bottom Line If you need a simple, reliable PoE switch that just works without setup, this is a solid choice.

Super simple. Was able to plug it in to 120v, unplug the router from the modem, plug this into the modem, then plug the router into this NETGEAR switch and WHILE 'Sling' was streaming with only about a five second pause in streaming and then it continued. After than I was able to use an open port on the switch to plug in a NETGEAR Nighthawk Dual-Band WiFi 7 Router RS140 and spend about 20 minutes getting that configured. After that I reconnected my 10 devices to the new router and threw away my old Tenda router which has seriously compromised security with a open back door for hackers denial of service attacks. Just a note, the router would not allow connection with the default password written on the bottom. I had to change it in the phone app and it worked like a charm. Just an FYI if you're planning the same thing. I'm a 70 year old caregiver for my 88 year old senile sister and my 68 year old fiance, so keeping them happy with their devices while I upgraded was paramount. Mission accomplished, plus I have more open WAN ports for a future outdoor wifi planned for later this year.

This was the perfect solution for feeding multiple devices from my Starlink internet. Netgear is a reputable brand and it has worked flawlessly forme. Definitely worth the extra dollars over the cheap unknowns.

This was exactly the POE switch I needed. Worked at a video collaboration vendor expo and needed POE and internet to power devices. I connected this to a Travel Router, AC1200 Dual-Band Wi-Fi for the internet and then 4 devices with 2 of them needing POE power - everything worked and had enough speed and bandwidth to join Teams and Zoom calls live.

I have bought a few of these for use on our campus and I can say that they are basically a steal for what you get. Not they don't have their issues. Here are my pros and cons: Pros- Price- Bar none this is the cheapest managed PoE switch I have been able to find. At $7.50 a port its basically unbeatable. Most commercial switches I have had quoted come out to about $30 a port. Yes greater functionality at that price, but not worth it if you don't need them. Power- It actually has a decent power budget. 62W over 8 ports which averages out to about 7.75W per port. This is plenty to run low power applications such as security cameras. You can still run things such as wireless access points, but don't expect to fully populate the switch with them. (Edit) If you are in need of a greater power supply per port, the GS316EPP has an astounding budget of 231Watts which works out to about 16W per port. Should be enough to power just about anything but the most power hungry PoE devices. Management- The fact that its actually manageable at this price. The features available are not spectacular by any means, but you probably are not buying this if you need in depth QOS settings. You can fully manage both the power and VLANs on it which is more than sufficient for basic networking. It does have a free management software that you can use, thought it does have some serious limitations. GUI- The web GUI is pretty straight forward with the home screen providing most of the basic device settings at a glance. Switching tab aside, settings are clear and concise. They also have helpful descriptions for those less familiar with networking terminology. Bandwidth- All 8 ports are gigabit capable and the switch does allow port aggregation allowing for a greater outbound bandwidth from the switch if you have a few high volume devices plugged into it. Cons: Management- As previously stated, this certainly isn't a state-of-the-art device. QOS settings are limited to bandwidth controls and only the most basic of Multicast settings are available. The free "central" management software also has a major limitation. It only works if the switches are in the same network as the computer/server hosting the management software. If your computer is in 192.168 and your switch is in 172.16, it will never find it. This isn't an issue if you are operating a flat network or have a management VLAN. GUI- Overall the GUI is great, but the VLAN management is very annoying to work with. For starters, the VLAN modes are not particularly well described, so figuring out which one does what you need is a matter of trial and error. The Advanced VLAN Management is particularly painful to work with, though it does offer the greatest flexibility in settings. This is primarily due to the interdependence of the PVID table and the VLAN port assignments. To change the PVID setting on a port, you must have the VLAN you are changing it to assigned. Or if you want to remove an assigned VLAN, but its the PVID, you must first remove change the PVID before you can remove it. These are on completely separate pages requiring navigation between the two when tweaking the settings. If you are going to be changing these frequently, be prepared to spend a lot of extra time doing so. Though less irritating, having to click edit on each individual VLAN to manage its assignment to ports is unnecessary and could have easily been on the main VLAN management page. CLI- Or lack thereof. For those of you who much prefer Putty to a web browser, that simply isn't an option. (Edit) Mac Table- Zero access to what is one of the most useful features in switching. Figuring out what is plugged into what port without it is basically just unplug the cable and see what goes down. Not great great for high availability devices and end users. TLDR: Best bang for buck for a managed PoE switch that you can find. Great if you need something just above plug-n-play. Just expect a configurable feature set comparable to the price.

I read many, many reviews here on Amazon and the web about sending power through RJ45 to BNC cameras ( I don't have IP cameras yet ), so I started with the NETGEAR 8 Port PoE Gigabit Ethernet Easy Smart Managed Essentials Switch (GS308EP) - with 8 x PoE+ @ 62W ( ASIN B08MBFLMDC ) since I only have 4 cameras and 1 camera is PTZ ( when I get IP cameras I am already set to manage the power, QoS, VLAN, etc with the switch ). I purchased 5 pairs Passive PoE Injector and PoE Splitter Kit with 5.5x2.1 mm DC Connector RJ45 Power Over Ethernet. I have a NETGEAR GS308 5 port switch which will provide communication to the GS308EP switch so I can access the admin page. With all that and reading the reviews, unfortunately I could not get it to work. No power being sent to the cameras and the question of WHY. I continued researching the WHY until I found from NETGEAR that in order for the GS308EP switch to communicate and be able to manage the power to the cameras the splitters had to be 802.3af/at compliant, if not the baluns WILL NOT work, and that I needed ACTIVE baluns, NOT passive like the first 5 pairs I purchased. I did find and watched a video "How to Install AHD CCTV Cameras using POE switch as Power Source" that helped me understand about the active baluns. I then purchased a 4-Pack Active PoE to 2.1mm DC - IEEE 802.3af/at compliant. I could not be more happier when I received the ACTIVE baluns and connected them cause everything was set, I was just waiting on the ACTIVE baluns. The ACTIVE baluns are the ones that worked for me with the setup mentioned above and I hope it helps other people out there that have basic knowledge, because there is no single page on the internet that provides you a solution, you have to dig and read many, many pages to do trial and error until it works. I love Netgear products and still have ( of course not connected ) a Netgear Internet Gateway Router with a built-in 4-port 10/100 Mbps Ethernet switch model RT314. Netgear is build with TRUST in mind. Thanks

Nice semi-smart switch, easy to manage from its web page. VLANs are easy to configure. POE works reliably.

Bought for a home monitoring system. HIghly reccommended by Grok and Gemini - seems to work just fine.

Fácil de administrar, interfaz amigable.

I bought this switch to setup VLAN that is part of my home network upgrading. For the VLAN function, it works well. But for POE, I have not yet tested as UniFi AP out of stock. BTW, I does not like the new interface for WebGUI. It has less option. I still prefer the old Web GUI.

ممتاز جدا

Work perfectly