Loctite Epoxy Instant Mix, Translucent Yellow 5 Minutes, 0.47 fl oz Syringe, Pack of 2

I can't speak to other applications but this was exactly what I was looking for. I needed a strong epoxy which would flow well into crevices but was thick enough not to run all over, this is about the consistency of cold maple syrup upon dispensing but hardens within a few minutes to tacky and then starts to solidify. I had a barrel shaped wiring harness with a number of wires close together, which would move and touch each other at extremes. I applied the epoxy to the wire ends, which were soldered in place, and then wrapped tape around the area to make a tube and then filled the area to make a solid epoxy plug. I did it once and let dry for a few hours and then did the process again. The result was exactly as desired, all the wires are encased in epoxy and the strain relief slides over the epoxy plug. The epoxy resin cures up very hard in 24 hours but it does not seem to be brittle. It fills gaps well and is not difficult to work with. If I was using this for any other application, I would ensure the work I wanted to connect was sanded and de-greased, to provide the epoxy something to grip onto. Perhaps this is the problem some folks are having who have rated this product low. I found it perfect for my needs.

Easy to use. Not a lot of pressure required to deliver the mixed fluids through the special syringe tube. Used it on a sockslide which is supposedly made out of ABS plastic. It's been working just fine, the glue is holding very well.

This stuff is incredible, I've been using it for years. The self-mixing applicator is genius. No more mixing yourself, just attach the tip and squirt and it's mixed as it comes out. The epoxy itself sets quickly (5 min) but flows like a gel/liquid for the first few minutes, so you have to plan ahead. It's workable for a couple more minutes until it hardens after 5 minutes or so. Will still be pliable/tacky for another 5 to 10 minutes. Yellows as it cures (does not cure clear). Still the best stuff I've ever used, you can get it places you can't get other mix-it-yourself epoxies. Super strong once cured. With the extra applicator you can legit cap the tube and get another use out of it if you don't use it all. There isn't much in the tubes but I find most of the time I don't need more than half anyhow.

I had recently purchased a amazing double wheel Barrow. It was top of the line and top of the line cost as well. I was very stupid and threw a large log in it. The wheelbarrow was heavy duty plastic and cracked. I purchased this and used An entire to whun on each side. So a total of 2 tubes, one on each side. I didn't really expect it to work.. And it didn't. Haha. But it was very easy to use and seemed to be high quality. I was just asking too much for the epoxy. Lol. I ended up taking the wheelbarrow apart and putting a plywood Cut out underneath. The epoxy has not broken loose completely yet, But it will soon. I do believe the plywood is going to be the winner lol. But Again I feel this is good a epoxy and I absolutely love the double tube. I can remember the daze of emptying to 2 or however much needed to use and mixing them together. This was a much easier way. Overall I would give it 4 stars. Even though it DIDN'T work!

Works great but don't pull unused contents of mixing nozzle back into the syringe- it's already mixed! Rookie error. I've ordered a bunch of extra mixing nozzles because the nozzle is thrown out after each application.

This adhesive—or epoxy—is so efficient, and so well-suited for application using the syringe method, that you avoid any waste or errors. I highly recommend it for the specific purpose I use it for: repairing speakers or re-coning speaker drivers.

This product is a chap alternative to other epoxies, but that is reflected in the product. The hardener is not effective and must be mixed manually, the stick is not strong. The strength is reduced compared to other epoxies, and after the solution has dried for several days, it is still sticky and not very strong. The product advertised setting in 5 minutes, however, it takes several hours for it to react and finish. The black push bar makes it easy to apply with little force, but do keep in note that it will be hard to push at first, and then after the epoxy starts moving it becomes a lot lighter to push and asker to over apply. I found it handy to start pushing and stop right after, and slowly apply more incrementally. PLEASE, PLEASE, do this is a WELL ventilated, before this dries, epoxy fumes are TOXIC, especially to people with asthma. This product is good for light, hobby crafts, as the price is good for that, but it should not be used for anything critical or beyond hobby crafts.

Takes a full day to set but works great for fixing artificial jewellery

Muy buen pegamento, muy buena calidad, solamente que es muy difícil volverlo a utilizar ya que, aunque quites la pipeta y le coloques la tapa es dificilisimo volverlo a utilizar. Hay que dejarlo secar por lo menos 12 hrs y listo, transparente 👍🏻

Its not that strong glue what i expect to be , but is doing the job.

Quickness of sealing Used to attach metal lamp to cement base.

Sehr zu empfehlen. Gut für unterwegs.