Pipe Wrap Kit

Holds the heat in the pipes around my legs on my dual exhaust on my bike. No more heating up my inner leg.

So far so good! Makes a huge difference. I used this to wrap my exhaust between my frame and transmission after installing dual exhaust. I have fuel lines on my frame rail I was worried may get hot. I put in some aluminum heat shield and wrapped the pipe with this and after running the truck for 30 minutes the frame and fuel lines are cool to the touch. I could even fully grab the exhaust pipe about a ft back from the manifold bare handed. It was warm but nowhere near burning hot. Ties were too short for 2.5 inch pipe so I used hose clamps.

It's a bit tricky to secure with metal zip ties and it's hard to get them tight enough by hand or with pliers. I would definitely go buy some more ties separately, because the two included ones are almost certainly not going to be enough. The ends do fray, of course, which is inherent to the material. I folded the ends under to hide and protect the fray. Some people wet it first. I didn't, and I really had no real problems applying it dry. Definitely wear gloves. You should probably wear long sleeves, too, in case you bump your arm into it or it drags across your skin. It'll definitely leave an itchy rash. It smokes noxious death chemicals at first. For cars and trucks, this isn't really an issue in my opinion, except to a small extent maybe for the car behind you, but for motorcycles, powersports, and other small equipment, be prepared for the Batman smokescreen. The color does gradually get darker, but it takes some time. Does it keep the heat in? It will lower the temperature, prevent burns if it's on your motorcycle pipes, and protect nearby components like wiring, but it's not a miracle product. For sound insulation, I haven't noticed any difference. For the money, I'm happy with it.

Great product for my 5.3 Silverado (2005). After rebuilding the motor and throwing on some headers, I was burning through my plug wires. I was running performance wires (in heat socks) but still didn't help much as the wire causing the issue couldn't be kept far enough away from the header. That's where this came in!. I ended up wrapping the plug wire itself with this as well as the header, using the provided metal zip ties on the wire, and running hose clamps on the header. Nothing against the provided ties, just needed more than 4. I bought the hi-temp silicone paint and allowed for it to get hot and seasoned (the smell is pretty bad too, but only lasted roughly 30 mins). Overall, great product, just wish I would have known the Titanium version of this wrap doesn't require the silicone paint.

Installed dry and worked well. I was able to stretch it tight on the pipe using plastic zip ties to hold it in place temporary until I was able to install the stainless ones provided. I cut off the plastic ties before starting up the machine. It insulates very well. Surface gets hot but not super hot. I will say it will not go as far as the chart for installation says, I would figure it at about 75% coverage.

I started with buying one of the cheap alternatives, thinking it was the same. I was sorely mistaken. The cheap ones bleed so much in the water. They also have more than double as many fiberglass pieces that flake off. I received so many fiberglass splinters trying to use the sheep alternatives. I end up throwing the cheap one away. Even after their app was done there was fiberglass everywhere. Pay the extra it’s worth it

The product is great, however, I am not smart enough to figure out how to wrap a taper, so I just sent it to be ceramic coated instead. It feels like a quality product, and looks awesome. I’ll likely use it on a motorcycle instead of my catted downpipe, and fully with expect it to work perfectly.

Wrap is a good material as always. Have to presoak before application. The only bad parts are the locking ties. They give you 4 but all so small it doesn’t fit around the pipe. Had to use my own clamps

Able to reduce heat significantly on my bike's exhaust running just next to my calves and radiating heat right up my thigh. Packaging says the kit includes a metal tie tensioning tool but none was included. The ties were decent but not secure enough in my opinion. Good to invest in some hose clamps.

La cinta térmica se ve bien, pero el kit no incluye los cinchos qué dice la publicación.

I bought this wrap to wrap my custom turbo exhaust manifold and part of my downpipe. It works great and puts up with the heat. It does smoke and smell for the first 15 minutes or so, then it's not so noticeable. I expect it will last a very long time. I didn't use the included SS bands as they were too short for my application. I used some longer SS bands that I had on hand instead to secure the wrap.

excellent product - easy to work with - looks great on bike

Applied on motorcycle pipes, looks great. Haven't rode enough to see if they fade. They will smoke for awhile and smell but it goes away after awhile. Easy to apply just make sure you wear gloves and coveralls because of the fiberglass in the wrap. Good stuff