I2C 0.91-inch OLED Display SSD1306 128x32 Pixels IIC 3.3V 5V White Character Display Compatible with Arduino and Raspberry Pi Including E-Book!

Items arrived on time, as shown and as described. Worked well with ESP/Pico/Pico2 (ssd1306) Library from PyPl, Greatly simplifying code, scrolling and simple graphics. Good value for 5 x display modules.

Works fine but take care to read the dimensions - it's not as big as it looks in the picture!

Useful little screens, well supported

This display works well for me, and works with my arduino.

Love these small displays, ideal for Ardunio projects etc. Never had an issue products from A-Z Delivery

Amazing little screen. Easily setup and gives a detailed, clear display. Nice form factor.

I bought these to replace another SSD1306 I had bought from aliexpress. These are of higher quality, brighter, and better defined pixels. I only needed to replace one screen, but I have replaced all screens with ones from this seller now as they are better. The seller also sent me a message after purchase with the datasheets and instructions attached - I didn't need this but I wish all sellers would do this, sometimes they can be difficult to track down. Would note also that the packaging was better than most, they came in a printed cardboard box with individual anti-static bags and with pins covered in foam for protection.

Not so easy to mount but can be done onto pcb card My project was a light meter with digital dispatch Good price in quantity buys (5)

These small OLED displays is nice to have for different kinds of projects. They are easy to interface, with them being I2C. There are also a lot a guides and support material online for these displays since they are so common. And since they are using the 1306 driver there are ready-made libraries in Arduino IDE for these displays. I need a display without the board, so i will have to desolder the display from the PCB. These displays has 14 pins, which are connected to the PCB, and the PCB board then has the 4 pins for I2C. I have briefly tested the displays, and so far they are working, so at this point i am satisfied with this purchase.

Bien pensé, facile a utilisé.

alles ok

/*El vendedor da un ejemplo que usa la libreria U8G2 que funciona si eliminamos o comentamos todas las lineas que dan error en la compilacion, yo uso la libreria de adafruit que da menos problemas y usa menos memoria. Yo uso lo siguiente y va superior:*/ #include <Wire.h> #include <Adafruit_GFX.h> #include <Adafruit_SSD1306.h> /* Declaración para un SSD1306 display 128x64 ó 32 conectado al bus I2C (SDA (A4), SCL (A5) pins). // Usar el adecuado, aunque si usamos el de 64 en una 32 funciona pero deforma, (aplasta), a 32 // Si usamos el de 32 en una 64 se muestra correctamente pero solo usa la mitad superior de pantalla. // descomentar el que interese.*/ //Adafruit_SSD1306 display(128, 64, &Wire, -1);//Pantalla 128x64 //Adafruit_SSD1306 display(128, 32, &Wire, -1);//Pantalla 128x32 //El(-1) = pin del Reset (-1 si comparte el pin reset del Arduino o la pantalla no lleva pin de reset) void setup() { // SSD1306_SWITCHCAPVCC = generate display voltage from 3.3V // Inicializa la pantalla para la direccion dada segun fabricante // Direccion 0x3C para esta 128x64 ó 32, aunque en la placa viene serigrafiada otra.(esta esta detectada con un escaneo al bus I2C) display.begin(SSD1306_SWITCHCAPVCC, 0x3C); } void loop() { display.display();// Muestra el logo grabado internamente. // Y ya poneis lo que querais, aqui y en el setup. }

Cercavo un piccolo display a basso costo da utilizzare nella realizzazione di un prototipo di un dispositivo elettronico; ho provato questo display e devo dire che sono rimasto molto contento, ottimo rapporto qualità prezzo: va bene per chi ha bisogno di poco spazio e bassa risoluzione: piccoli testi (anche scorrevoli), semplici animazioni, ecc. Io lo ho utilizzato con un micropcontrollore ESP32 (si trovano molte librerie online), ma ovviamente lo si può utilizzare con qualsiasi microcontrollore (ad es. con le schede Arduino, STM Nucleo, ecc.). Il collegamento I2C rende il collegamento veloce (bastano 4 cavi).