2 Autosmart Kl-35100rk Red Oval Sealed LED Turn Signal and Parking Light Kit with Light, Grommet and Plug for Truck,Trailer (Turn, Stop, and Tail Light)

More impressed than I thought I would be. These lights were nicer than I thought they would be given a price. They came nicely packed, and the packaging was intact. The lights are bright and do the job well I was most impressed with the rubber grommets that surround the light. I had some Concerns in this area. I was worried that they would be a hard plastic and difficult to make fit in these Recesses. The rubber was Mailable and of good quality.. It fit in the recess Perfectly. The electrical plugs and recesses were extremely well done. There was even a little bit of corrosion protection grease inside the recesses. They had also put a little tape over the recesses to keep the grease in and the dirt out.The only odd thing was it the wire leads have been stripped approximately 1/8 of an inch. Why bother? I just stripped them myself. I would say it was a great product.

My trailer was built before LED lighting was common place so they were not very bright, especially the turn signals. These lights were the same size so I expected them to fit well, which they did. What I didn't expect was that the orig lights had the exact same connector so this was truly a plug and play installation. With a flat screwdriver I pulled the orig lights out then pushed, pulled, tugged to get the new ones fully seated (this was a good thing... they were a snug fit so no leaks) and they worked flawlessly. Much brighter and more noticeable than the original lights so now I won't be as concerned while towing. If they fail early in any way I'll update this review but so far they are exactly what I wanted. As usual, Amazon shipped in a day or two and the packaging was safe and secure. Now I'm off to find quality LED marker lights.

Of course I read the reviews however, the reviews are only part of my decision process. Sometimes you just have to take a chance and try the product for yourself and this is what I did. I'm a very critical individual and could find fault in most any design however these taillights are of first rate build quality. And those who have criticized the rubber gasket, I don't know what planet they come from because they are of first rate quality. I would definitely recommend these to anyone who has old faded incandescent lamps in their vehicle. I must mention that during installation, be sure to seat the gasket in its hole completely before inserting the light. Also care must be taken inserting your existing plug as these break very easy. No worries though, a couple butt connectors and the supplied plugs work great. Once the gasket is fully seated, use a few squirts of Windex or like glass cleaner on the gasket. It allows the lamp housing to slide into the gasket much easier especially if the hole is on the small side making inserting the lamp a bit of a challenge. Use the glass cleaner and it just slides right in. They look great and work as they should!

Easily popped the old lights out and these fit back in perfectly. They come with a wiring harness but since they're standard my existing harness plugged right in, no rewiring at all. Lights are much brighter than the originals and i highly recommend them from a safety standpoint. Great quality lights. The photo shows new LEDs on the left, old incandescent on the right. Cheers

Good replacement fit but I used the original rubber boots because they were more snug and softer rubber making a better weather seal than the rubber on these. Nice and bright. Saved money buying 2 because local stores sold 1 for $2 less than these 2.

I have an old Haulmark box trailer. I didn't buy it new so I'm guessing 15-20 years old. My trailer had two of these lights per side. 4 total. It took longer to get the old one's out than it took to put the new ones in. The new rubber seals fit perfectly. The light assemblies fit very snugly. I'm a veteran at this kind of stuff so it was easy on the brain but a little tough on the muscles. It took a lot of pressure to get them in place correctly. I used lubricant, grease in this case to get the light into their correct seating into the new rubber seals. Once done, plugged in, really nice. I didn't even have to rewire anything. The plugs or harnesses fit perfectly. I would buy these again.

Bought these to replace incandescent lights on a boat trailer because the old ones seemed dim. These are nice and bright. I think they really look sharp. Install was easy as I already had a matching 3 terminal connector on my trailer. They have already survived being underwater for two boat launches, so I believe they are waterproof and will probably not have any issues due to water.

Great choice to replace the lights on my EZ Tow car dolly. Very inexpensive. Popped the old ones out and put the new ones in. It helps to have some wire joints like the 3M Scotchlok bits here: https://www.amazon.com/3M-Scotchlok-Electrical-560B-BOX-Retardant/dp/B004RCOZ6C/ref=sr_1_12?keywords=3m+wiring+kit&qid=1559757402&s=gateway&sr=8-12. I will post an update after a few months and report on reliability of the Chinese LEDs.