Reboot Welding Electrode Holder Twist Type 400AMP Full Copper Heavy Duty Electrode Clamp Accessories for Welding Machine ARC MMA Welder

This welding handle is a bit different. you twist the head to loosen and tighten the rods. There is no spring to wear out, and this is more solid than the spring type, so it holds the rods better. It is a bit harder to get used to if you have used the spring clip type, but it works better. it arrived timely, and the price was not too high. I'm very satisfied with it.

Good enough quality for DIY guys but would never stand up to all day use.

awesome. as advertised. nothing special. it didnt make me a better welder

I waited a couple days of use before putting out a review. Shipped to my house next day with prime membership. When I opened it I noticed that the head was a 2 piece assembly. I thought that it wouldn’t hold up long, needless to say it’s held up quite well for the first job I’ve put it through. Running constant 150 amps through this stinger welding a bunch of half inch plate for a winch mount for the car trailer, and this thing hasn’t let me down. The wire is held inside the collar by not one but two set screws. The cavity is a little over an inch to allow a good bit of wire through for that extra bit of comfort in the back of your mind. I am running #2 wire without an issue. The handle took a bit of time getting used to but not long at all, just a few welds. So far so good. And for the price it’s well worth it. I recommend this stinger and have no doubt that if I have an issue customer service will take care of it without an issue.

It's a great twist style stinger for its price but definitely not durable, when in use for industrial environments. I use 3/16 rod and above and I did notice that the insulation is prone to cracking after long use. I did use it non stop for 3 days, 10 hours each and it break and stop holding the rod, I can see that it would be great to buy if your a hobbist welder or interested this particular style as it's cheap. I would definitely invest in a more quality product some where else if using a industrial setting or consistent use.

I did not see instructions in my box, but was easy enough to figure out how to make it work. This handle gives a nice angle to weld so your wrist is not bent like using the "clamp" style. To install the lead wire from my welder, I had to unscrew the red handle all the way off the top. There is a spring and a rod in the top part, so be careful when unscrewing it apart. It came with two set screws, a small plate and a hex key to install the lead wire. Then, insert that part back into the bottom of the handle and screw on the top part to the top of the handle. The way it holds the welding rod is by unscrewing the handle a little and inserting it into the tip. Then, twisting the red grip the other way to tighten until it is secure. Twist it the other way to release the stub and insert a new rod, etc. It is very well made and not too heavy. This handle really holds the lead wire and welding rod without issues.

Great design except for multi directional rod placement, built for high Temp work custom line size and length.

Junk, Terrible Design, Dangerous⚡️⚡️⚡️Shock Hazard!!!! Buy Something with better design!!! Purchase this a while back and had a job come up that required ALOT of stick welding...went thru all troubles to remove my old electrode holder which was very old but always held on for the many years of service and put new one, as soon as I put first electrode in and twisted the handle, which is supposed to clamp down firmly so electrode doesn't fall out!! After first 5 electrodes being pulled out in mists of weld which is maddening btw!!! Had to disassemble the whole handle, finally figured out the rod that pushes the clamping mechanism was way too short. I cut a new piece replacing the faulty factory one, but now everytime I twist the handle to tighten it, the top of the two halves trys to push apart, I tried a slightly shorter rod for clamping assembly but anything shorter and it will not hold!!!!! Now I'm stuck with this junk!

All ReBoot products are good...and this tough, comfortable electrode holder is no different...good quality & great value for money !

Tien l'électrode en place très fortement à comparer avec les anciens modèles de pinces (normal) du genre de ceux de marque Lincoln, beaucoup plus sécuritaire et de conception de qualité supérieure, a une fraction du prix,

Very solid Works great Very happy with it

Excellent et très abordable

Cheaply made would buy something better next time which will last for life